SN74ALVTH16374 - 2.5-V/3.3-V 16-Bit Edge-Triggered D-Type Flip-Flops With 3-State Outputs

The 'ALVTH16374 devices are 16-bit edge-triggered D-type flip-flops with 3-state outputs designed for 2.5-V or 3.3-V V_CC operation, but with the capability to provide a TTL interface to a 5-V system environment. These devices are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers.

These devices can be used as two 8-bit flip-flops or one 16-bit flip-flop. On the positive transition of the clock (CLK), the flip-flops store the logic levels set up at the data (D) inputs.

A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus lines without need for interface or pullup components.

OE does not affect internal operations of the flip-flop. Old data can be retained or new data can be entered while the outputs are in the high-impedance state.

Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level.

When V_CC is between 0 and 1.2 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.2 V, OE should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

The SN54ALVTH16374 is characterized for operation over the full military temperature range of -55°C to 125°C.

The SN74ALVTH16374 is characterized for operation from -40°C to 85°C.

Products containing the "SN74ALVTH16374" keyword are: SN74ALVTH16374DL , SN74ALVTH16374DL , SN74ALVTH16374DLR , SN74ALVTH16374DLR , SN74ALVTH16374GR , SN74ALVTH16374GR , SN74ALVTH16374GRE4 , SN74ALVTH16374GRG4 , SN74ALVTH16374KR , SN74ALVTH16374KR , SN74ALVTH16374VR , SN74ALVTH16374VR

• State-of-the-Art Advanced BiCMOSTechnology (ABT) Widebus™ Design for 2.5-V and 3.3-V Operation and Low Static Power Dissipation
• Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 2.3-V to 3.6-V V_CC)
• Typical V_OLP (Output Ground Bounce) <0.8 V at V_CC = 3.3 V, T_A = 25°C
• High Drive (-24/24 mA at 2.5-V V_CC and -32/64 mA at 3.3-V )
• Power Off Disables Outputs, Permitting Live Insertion
• High-Impedance State During Power Up and Power Down Prevents Driver Conflict
• Uses Bus Hold on Data Inputs in Place of External Pullup/Pulldown Resistors to Prevent the Bus From Floating
• Auto3-State Eliminates Bus Current Loading When Output Exceeds V_CC + 0.5 V
• Latch-Up Performance Exceeds 250 mA Per JESD 17
• ESD Protection
  • Exceeds 2000 V Per MIL-STD-883, Method 3015
  • Exceeds 200 V Using Machine Model
  • Exceeds 1000 V Using Charged-Device Model, Robotic Method
• Flow-Through Architecture Facilitates Printed Circuit Board Layout
• Distributed V_CC and GND Pin Configuration Minimizes High-Speed Switching Noise
• Package Options Include Plastic Shrink Small-Outline (DL), Thin Shrink Small-Outline (DGG), Thin Very Small-Outline (DGV) Packages, and 380-mil Fine-Pitch Ceramic Flat (WD) Package

Widebus is a trademark of Texas Instruments.