SN74LVTH16245A - 3.3-V ABT 16-Bit Bus Transceivers With 3-State Outputs

The 'LVTH16245A devices are 16-bit (dual-octal) noninverting 3-state transceivers designed for low-voltage (3.3-V) V_CC operation, but with the capability to provide a TTL interface to a 5-V system environment.

The devices are designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs or the A-port outputs or place both output ports into the high-impedance mode. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports is always active and must have a logic HIGH or LOW level applied to prevent excess I_CC and I_CCZ.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.

When V_CC is between 0 and 1.5 V, the devices are in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, OE should be tied to V_CC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

These devices are fully specified for hot-insertion applications using I_off and power-up 3-state. The I_off circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict.

Products containing the "SN74LVTH16245A" keyword are: SN74LVTH16245ADGGR , SN74LVTH16245ADGGR , SN74LVTH16245ADGGRG , SN74LVTH16245ADGGRG4 , SN74LVTH16245ADGVR , SN74LVTH16245ADGVR , SN74LVTH16245ADGVR(LL245 , SN74LVTH16245ADL , SN74LVTH16245ADL , SN74LVTH16245ADLG , SN74LVTH16245ADLG4 , SN74LVTH16245ADLR , SN74LVTH16245ADLR , SN74LVTH16245AGQLR , SN74LVTH16245AGRDR , SN74LVTH16245AGRDR , SN74LVTH16245AZQLR , SN74LVTH16245AZQLR , SN74LVTH16245AZRDR , SN74LVTH16245AZRDR

• Members of the Texas Instruments Widebus™ Family
• State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low Static-Power Dissipation
• Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V V_CC)
• Support Unregulated Battery Operation Down to 2.7 V
• Typical V_OLP (Output Ground Bounce) <0.8 V at V_CC = 3.3 V, T_A = 25°C
• Distributed V_CC and GND Pins Minimize High-Speed Switching Noise
• Flow-Through Architecture Optimizes PCB Layout
• I_off and Power-Up 3-State Support Hot Insertion
• Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
• Latch-Up Performance Exceeds 500 mA Per JESD 17
• ESD Protection Exceeds JESD 22
  • 2000-V Human-Body Model (A114-A)
  • 200-V Machine Model (A115-A)

Widebus is a trademark of Texas Instruments.